Combination of recuperator with exhaust air intake unit for use in mechanical ventilation systems
https://doi.org/10.22227/2305-5502.2023.3.3
Abstract
Introduction. One of the most common ways to save heat energy and money is the use of recuperator units in mechanical ventilation systems. In this article, we will talk about the modernized air recuperator. In the process the design feature, layout and operation algorithm of this heat exchanger device will be demonstrated. In order to increase the choice of type and designs of air heat exchangers, designers will be offered and described the variant of designed combined recuperator with an exhaust air intake device from the room, which in the process will be one of the versions of the device increasing the efficiency factor in mechanical ventilation systems. The recuperator is an indispensable element for modern unique buildings and structures.
Materials and methods. The recuperator is proposed as an analogue of existing ones and belongs to the field of energy saving in mechanical ventilation systems.
Results. The efficiency increase in comparison with analogues is carried out due to: the use of the recuperator as a combined exhaust air intake unit from the room, an increase in the area of contact of heat carriers, a special internal structure capable of more uniform heat transfer, an atypical arrangement of the recuperator installation to avoid freezing and "defrosting" of condensate at the heat transfer surface. The heating flow of the supply air through the combined recuperator with the exhaust air intake device from the room in the mechanical ventilation system is regulated by automation to maintain a more comfortable supply temperature in the room.
Conclusions. The new design acquires an increased efficiency compared to its analogues.
About the Authors
D. O. Khlopitsyn
Moscow State University of Civil Engineering (National Research University) (MGSU)
Russian Federation
Russian Federation
Dmitrii O. Khlopitsyn — postgraduate student
26 Yaroslavskoe shosse, Moscow, 129337
ID RSCI: 1107240, Scopus: 57224204063
A. G. Rymarov
Moscow State University of Civil Engineering (National Research University) (MGSU)
Russian Federation
Russian Federation
Andrey G. Rymarоv — Candidate of Technical Sciences, Associate Professor, Head of the Department of Heat and Gas Supply and Ventilation
26 Yaroslavskoe shosse, Moscow, 129337
ID RSCI: 665928, Scopus: 7801333552, ResearcherID: AFM-6219-2022
References
1. Mikheyev M.A., Mikheyeva I.M. Basics of heat transfer. Moscow, Energiya, 1973; 319. (rus.).
2. Bykov L.V., Molchanov A.M., Yanyshev D.S. Fundamentals of computational heat transfer and hydrodynamics. Moscow, URSS, 2019; 200. (rus.).
3. Vidin Yu.V. Engineering methods for calculating heat transfer problems. Moscow, Infra-M, 2018; 166. (rus.).
4. Nashchokin V.V. Technical thermodynamics and heat transfer. Moscow, Higher School, 1975; 496. (rus.).
5. Kudinov I.V. Mathematical modeling of hydrodynamics and heat transfer in moving fluids : monograph. St. Petersburg, Lan′, 2015; 208. (rus.).
6. Vinogradov S.N., Tarantsev K.V., Vinogradov O.S. Selection and calculation of heat exchangers : textbook. Penza, PGU Publ., 2001; 100. (rus.).
7. Zhukauskas A.A. Convective transport in heat exchangers. Moscow, Nauka, 1982; 47(rus.).
8. Samarin O.D., Yatsyna V.A. Research of the dependence of the thermal efficiency of the plate heat exchanger from the ventilation unit size. Plumbing, Heating, Air-Conditioning. 2021; 2(230):71-73. EDN NDMEZG. (rus.).
9. Borowski M., Karch M., Kleszcz S., Sala P., Waryan G. An experimental and numerical investigation of the thermal and non–thermal efficiency for counterflow heat exchanger. E3S Web of Conferences. 2019; 128:04008. DOI: 10.1051/e3sconf/201912804008
10. Lamlerd B., Bubphachot B., Chompookham T. Experimental investigation of heat transfer characteristics of steam generator with circular-ring turbulators. Case Studies in Thermal Engineering. 2023; 41:102549. DOI: 10.1016/j.csite.2022.102549
11. Belonogov N.V., Pronin V.A. Optimization of geometric parameters of cross-flow plate recuperators. Journal of International Academy of Refrigeration. 2008; 1:21-23. EDN JXORYH. (rus.).
12. Karapuzova N.Yu., Fokin V.M. Calculation of heat exchangers: guidelines for course and diploma design. Volgograd, Volgograd State University of Architecture and Civil Engineering, 2013; 67. EDN WABVMN. (rus.).
13. Chompookham T., Chingtuaythong W., Chokphoemphun S. Influence of a novel serrated wire coil insert on thermal characteristics and air flow behavior in a tubular heat exchanger. International Journal of Thermal Sciences. 2022; 171:107184. DOI: 10.1016/j.ijthermalsci.2021.107184
14. Rutkvskiy A.L., Makoeva A.K., Korobkin R.S. Research into cathodic processes in the electrolysis of alkaline lead solutions. Science and Business: Ways of Development. 2021; 1(115):30-33. EDN EJDJJJ. (rus.).
15. Kleszcz S., Jaszczur M., Pawela B. An analysis of the periodic counterflow heat exchanger for air-to-air heat recovery ventilators. Energy Reports. 2023; 9:77-85. DOI: 10.1016/j.egyr.2023.03.088
16. Vdovichev A.A. To the question of determining the temperature efficiency of plate cross-flow air recuperators. Bulletin of the Eurasian Science. 2022; 14(5). EDN XYXUEV. (rus.).
17. Golijanek-Jędrzejczyk A., Mrowiec A., Kleszcz S., Hanus R., Zych M., Jaszczur M. A numerical and experimental analysis of multi-hole orifice in turbulent flow. Measurement. 2022; 193:110910. DOI: 10.1016/j.measurement.2022.110910
18. Belonogov N.V. Heat recovery in cross-flow plate recuperators. Plumbing, Heating, Air-Conditioning. 2012; 2(122):75-83. EDN RHWDYL. (rus.).
19. Vdovichev A.A. Numerical study of heat transfer and aerodynamics in an open-type cross-flow heat exchanger. The Eurasian Scientific Journal. 2022; 14(2). (rus.).
20. Demidochkin V.V., Kostuganov A.B., Cherchayev A.A. Determination of heat technical efficiency of laminated heat recover. Bulletin of the Orenburg State University. 2018; 6(218):123-13DOI: 10.25198/1814-6457-218-123. EDN HNFKOY (rus.).
21. Vdovichev A.A. Features of numerical simulation of a plate cross-precision air recuperator. The Eurasian Scientific Journal. 2021; 5. (rus.).
22. Krasnov Yu.S. Installation of industrial ventilation systems. Moscow, Stroyizdat, 1983; 245. (rus.).
23. Krasnov Yu.S., Borisoglebskaya A.P., Antipov A.V. Ventilation and air conditioning systems. Recommendations for design, testing and commissioning. Moscow, Termokul, 2006. (rus.).
24. Samarin O.D. Fundamentals of ensuring the microclimate of buildings : textbook. Moscow, ASV, 2014; 203. (rus.).
25. Kamenev P.N., Tertichnik E.I. Ventilation. Moscow, ASV, 2006. (rus.).
26. Pachkin S.G., Kotlyarov R.V., Shevtsova T.G., Ivanov P.P., Li S.R., Presnova A.S. Development of an automated control system for plenum exhaust ventilation. Modern High Technologies. 2022; 1:80-84. DOI: 10.17513/snt.39013. EDN CYYMBL. (rus.).
27. Vlasenko O.M., Sorokin A.S., Abdulayev S.Kh. Ventilation heating during automation of industrial buildings of light industry. Design and technologies. 2015; 50(92):70-77. EDN VXLCNT. (rus.).
28. Halawa E., van Hoof J. The adaptive approach to thermal comfort: A critical overview. Energy and Buildings. 2012; 51:101-110. DOI: 10.1016/j.enbuild.2012.04.011
29. Arkhipov G.V. Automatic regulation of ventilation and air conditioning. Principal technological schemes of automatic control systems. Moscow, Gosenergoizdat, 1961; 176. (rus.).
Review
For citations:
Khlopitsyn D.O., Rymarov A.G. Combination of recuperator with exhaust air intake unit for use in mechanical ventilation systems. Construction: Science and Education. 2023;13(3):49-59. (In Russ.) https://doi.org/10.22227/2305-5502.2023.3.3
Views:
238
Email this article 
